MOULD CLEANING
AND STRIPPING SOLVENT
FOR CROSSLINKED OR FRESHLY
CURED RESINS
POLYESTER, POLYURETHANE, EPOXY and Bis-GMA MATRICES
ALTERNATIVE SOLVENT TO NMP AND NEP
Guaranteed free from chlorinated solvents
NO HAZARD OR WARNING PICTOGRAM
(CLP 1272 GHS Regulation)
iBiotec FAST CLEAN STRIPPER
Not classified flammable
Guaranteed free of hazardous, harmful,
irritating, or sensitising substances
Slightly volatile
Reduced consumption
SMP optimisation
Solvent Management Plan
(IED Directive)
ODP 0
GWP 0
Easily and quickly biodegradable
FIELDS OF USE
Elimination of pre-cured polyepoxides in the manufacture of construction materials, paints, coatings, floor resins, paving, aggregates, laminates, castings, gel coats, car components, structural elements for the aeronautic and spacial sectors, transformers, turbines, switches and other electrical equipment, wind turbine components; solder mask, SMDs, touch-resistant coatings for home appliances, sports and leisure equipment, tennis racquets, skis, sailboards, golf clubs, gliders, musical instruments, fishing rods.
Elimination of UP (or UPR) resins, Aliphatic homopolymers, semi-aromatic and homo co-polyesters and aromatic co-polyesters, pre-cured, in the manufacture of laminated components, top coating, under coating, car or boat equipment, stripping of moulds, encapsulation resins, components for sheet moulding compound (SML) machines, bulk moulding compound (BMC) injection machines, mineral moulding compound (MMC) injection machines, CIC (Continuous Impregnated Compounds). Cleaning of equipment for contact moulding, vacuum moulding, infusion moulding, autoclave moulding, simultaneous projection, filament winding, presses.
Elimination of polyurethane elastomers (Carbamates) including MDI, TDI and new generation NDI, PU (compact or foam). Stripping of moulds for low-pressure casting, including resins for RIM processes, high-pressure equipment for simultaneous projection, cured foams for sealing, wedging, insulation, or aerosol expanding foams.
PHYSICO-CHEMICAL PROPERTIES TYPICALS
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Appearance |
Visual |
Clear |
- |
|
Colour |
Visual |
Amber |
- |
|
Smell |
Olfactory |
Light, characteristic |
- |
|
Density at 25°C |
NF EN ISO 12185 |
1090 |
kg/m3 |
|
Refraction index |
ISO 5661 |
1.4660 |
- |
|
Freezing point |
ISO 3016 |
+7 |
°C |
|
Water solubility |
- |
>40 |
% |
|
Kinematic viscosity at 40°C |
NF EN 3104 |
1.5 |
mm²/s |
|
Acid index |
EN 14104 |
<1 |
mg(KOH)/g |
|
Iodine index |
NF EN 14111 |
0 |
gI2/100g |
|
Water content |
NF ISO 6296 |
<1 |
% |
|
Residue after evaporation |
NF T 30-084 |
<0.1 |
% |
|
PERFORMANCE PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
KB index |
ASTM D 1133 |
>180 |
- |
|
Evaporation speed |
- |
>3 |
hours |
|
Volatility index nBuAC=1 |
NF T 30.30 |
1.4 |
Quotient |
|
Evaporation index DEE=1 |
DIN 53.170 |
nm |
Quotient |
|
Surface tension at 20°C |
ISO 6295 |
27.7 |
dyne/cm |
|
Copper blade corrosion 100 h at 40°C |
ISO 2160 |
1b |
Measured value |
|
Aniline point |
ISO 2977 |
nm |
°C |
|
FIRE SAFETY PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Flashpoint (closed tank) |
NF EN 22719 |
80 |
°C |
|
Self-combustion point |
ASTM E 659 |
>200 |
°C |
|
Lower Explosive Limit |
NF EN 1839 |
2.6 |
% (volume) |
|
Upper Explosive Limit |
NF EN 1839 |
28.5 |
% (volume) |
|
Explosive, oxidising agent, flammable, highly or extremely flammable substance content |
CLP Regulation |
0 |
% |
|
TOXICOLOGICAL PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Anisidine index |
NF ISO 6885 |
<2 |
- |
|
Peroxide index |
NF ISO 3960 |
<5 |
meq(O2)/kg |
|
TOTOX (anisidine index+2x peroxide index) |
- |
12 |
- |
|
CMR, irritant and corrosive substance content |
CLP Regulation |
0 |
% |
|
Residual methanol content from transesterification |
GC-MS |
0 |
% |
|
ENVIRONMENTAL PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Water hazard |
WGK Germany |
1 without hazard for water |
class |
|
Primary CEC biodegradability 21 days at 25°C |
L 33 T82 |
>80 |
% |
|
OECD easy biodegradability 301 A over 28 days Disappearance of COD |
ISO 7827 |
>80 |
% |
|
OECD easy and ultimate biodegradability 301 D over 28 days Biodegradation at 67 days |
MITI amended |
>70 |
% |
|
Bioaccumulation n-octanol water sharing index |
OECD 107 |
-1.35 |
KOW log |
|
Steam pressure at 20°C |
- |
<0.1 |
hPa |
|
VOC content (Volatile Organic Compounds) |
- |
renewable carbon content > 90% |
% |
|
Total halogen content (Chlorine Fluorine Bromine) |
Bomb calorimeter GC MS |
0 |
% |
|
Benzene content |
LPCH |
0 |
% |
|
Aromatic solvent content |
LPCH |
0 |
% |
|
Environmentally-hazardous substance content |
- |
0 |
% |
|
Content of compounds with GWP |
- |
0 |
% |
|
Content of compounds with ODP |
- |
0 |
% |
|
Carbon assessment, life cycles analysis. |
ISO 14040 |
6.40 |
Kg carbon equivalent |
